Pay in installments of $109.75 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 20 - Jul 25
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Fits 1967-1969 Camaro, 283-400ci, Long Tube Headers - Black Ceramic 2105-3HKRHooker Headers announces the release of their new long tube headers for the classic 1967 1969 F Body (Camaro Firebird) and 1968 1972 X Body vehicles (Nova, Omega, Ventura, Apollo). These headers bring modern features and fitment to these classic platforms. Application fits motors with standard port heads. Features: Long tube geometry designed for maximum ground clearance and optimized engine compartment fitment. 3 8? laser cut flanges, TIG welded and
Hooker Headers announces the release of their new long tube headers for the classic 1967-1969 F-Body (Camaro/Firebird) and 1968-1972 X-Body vehicles (Nova, Omega, Ventura, Apollo). These headers bring modern features and fitment to these classic platforms. Application fits motors with standard port heads.
Features:
- Long tube geometry designed for maximum ground clearance and optimized engine compartment fitment.
- 3/8? laser cut flanges, TIG welded and flat finished for maximum strength and a leak free seal.
- O2 bungs included for compatibility with EFI systems or air/fuel ratio meters (plugs also included).
- Darksides Black Ceramic Coated
- 3? long-taper collectors for smooth exhaust flow transition from the headers to the exhaust system.
- Application fits motors with standard port heads.
- Compatible with straight and angle plug heads.
- Compatible with all stock manual and power steering boxes.
- Compatible with GM 152 and 168 tooth starters.
- Compatible with stock A/C evaporator case.
- Compatible with stock floor shift automatic and manual transmissions. Column shift automatics require the use of Lokar, or similar, aftermarket shift linkage.
- Compatible with Ridetech Tru-Turn steering system.
- Compatible with aftermarket large sump oil pans.
- Bolt-in installation capability with new Hooker 2.5? and 3? exhaust systems for these applications, with available adapters.
- Constructed with slip-fit collector for maximum ground clearance
Specs:
| Bolt Size | 3/8-16 x 3/4 |
|---|---|
| Brand | Hooker |
| CARB (California) Compliant | No |
| Clearance Category | Exhaust |
| Collector Diameter | 3.00 inch |
| Discount Percentage | 26-50% |
| Emission Code | 4 |
| Engine | Chevrolet Small Block Gen I |
| Flange Size | 3/8 Inch |
| Header Finish | Black Ceramic |
| Header Style | Long Tube |
| Primary Tube Dia. | 1-3/4 inch |
| Product Type | Headers |
| Sale Category | Exhaust |
| Tube Material | Mild Steel |
Application:
| Year | Make | Model | Submodel |
|---|---|---|---|
| 1969-1972 | Chevrolet | Nova | Base |
| 1971-1972 | Pontiac | Ventura | Base |
| 1968 | Chevrolet | Chevy II | Nova |
| 1967-1969 | Chevrolet | Camaro | Base |
| 1967-1969 | Chevrolet | Camaro | RS |
| 1970-1972 | Buick | Skylark | 350 |
| 1968-1972 | Buick | Skylark | Base |
| 1968-1972 | Buick | Skylark | Custom |
| 1968-1972 | Oldsmobile | Cutlass | Base |
| 1972 | Oldsmobile | Cutlass | Cruiser |
| 1968-1972 | Oldsmobile | Cutlass | S |
| 1968-1970 | Pontiac | LeMans | Base |
| 1969-1970 | Pontiac | LeMans | Safari |
| 1970 | Pontiac | LeMans | Sport |
| 1967-1969 | Chevrolet | Camaro | SS |
| 1967-1969 | Chevrolet | Camaro | Z28 |
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.3 ★★★★★
Based on 21 reviews
Sort
Product Reviews
★★★★★ 4
Reasonably adequate room divider
Size: 4 Panel-88'', Color: Beige
I'm reviewing this as I assemble it.
Couple things:
1. I didn't expect as much assembly. I've ordered dividers before and they more-or-less came as one unit. Sometimes the panels needed screwing together. These require complete assembly and come largely as three rods: two make up vertical columns and snap together. Another one (called part "C") makes the horizontal columns and you have two of these per panel (one attaches to part "A" and the other part "B"). These parts are metal with a plastic shim. Using the wood screws to attach to part "C" is a real pain in the neck. There's not much holding the panel in place so it's a little tricky.
One tactic I've found while I'm assembling that works for the initial connections from parts A and B to their respective "C" rods is to hold the screw in place with a screw driver and then rotating the rod around the screw. This will do a number on your hands if you aren't wearing gloves. This obviously doesn't work when completing the connection.
Using a driller driver on this is really near impossible because there isn't anything you can use to secure it in place. You can use it on the first panel, but as it gets longer, it becomes increasingly difficult and because it isn't wood, it's really tight. I considered drilling larger pilot holes but since there are only 4x4=16 screws I need to screw in, I just decided to use my screw driver to complete it.
2. Also related to assembly. When completing the panels (attaching parts "A" and "B" to parts "C" that have the cloth cover on it), you have to be careful that when you tighten that side that it isn't loosening the other side. Because the pilot holes are so tight, you can end up rotating the rod, which rotates it in the same direction as looser on the original side. Having someone hold the "C" rod in place while you screw it in is probably the easiest approach. I didn't have a 2nd person, so I just had to keep flipping back and forth and tightening both sides as I screwed it in. Not the worlds biggest deal, but annoying nonetheless.
3. The way the instructions are written, they seem to suggest building this thing progressively; that is, you do panel 1, then 2, connect them together, then do 3 and connect it, etc. I took a different route that I suspect saved me quite a bit of trouble, and I assembled all four panels first and THEN connected everything together.
4. For the love of God make sure you check that the plastic tip is on the same side for every panel. Otherwise, you have to take one side apart again and reverse it. On the bright side, if this happens, you've essentially bored out the pilot holes to be the correct size... which is having me question if I shouldn't have just bored them out to the appropriate width in the first place.
5. Attaching all of the panels together is also an enormous pain in the ass unless you happen to have an 88" long elevated surface. Attaching the legs either requires you to elevate one side, which will invariably twist the inexplicably cheap material in the bottom connectors... or you can attach them sideways... or you can put this thing upright, having two people hold the panels in place while you use the allen wrench to tighten the bolts on the underside. None of those are particularly great options.
NOW on to the utility itself.
1. The panels do let some light through (I didn't believe their advertising, and that was one of the reasons that I bought beige, is that I wanted it to not be too dark). They aren't transparent though, so it isn't that far off from their description. They functionally work great, and keep the mess of wires hidden and when I'm sitting at my desk, actually reflect quite a bit of light into my office. Great!
2. My wife has described these as "the most hideous piece of furniture ever conceived of by man." So it does not have spouse approval factor. Granted, she will seldom be in my office area, so that isn't the end of the world.
3. These are really hard to align in a way that doesn't look a little tacky. There are some plastic connectors but they don't do a bang up job of keeping these in place. Each panel is slightly tilted and it's... quite obvious. I may at some point make my own improvements to these to help make them more level. It's not a particularly expensive product so I wasn't expecting much so it's fine and I'm not going to ding them on the rating because of it.
All said, would I buy this product again? Probably not. It's assembly was ~90 minutes which is about 75 minutes longer than I was anticipating spending on this (not including the 5 minute writeup that I'm doing here). But am I going to return it? Also no, if for no other reason I'd be just as annoyed taking it apart and putting it in the original box to return it.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 31, 2023
★★★★★ 5
Great value for price. Cute, lightweight. Could be used anywhere.
Size: 3 Panel, Color: White
Nice, lightweight. Good value for price. It's exactly what I needed for my hallway to keep my cats separate from each other. I used two zip ties to eyescrews in door trim and it opens up perfect to wall. Warm air gets thru and cats can see out/in. But can't get under or over. It's perfect for my use!!!!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 23, 2025
★★★★★ 5
Great seller and really nice items!
Size: 6 Panel, Color: White
These room dividers are really lovely. They are great quality and just perfect for providing privacy in a sunroom while still allowing light in to keep the room sunny. I highly recommend.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 24, 2026
★★★★★ 5
Nice divider!
Size: 4 Panel, Color: White
I use this as a "barrier" to keep my cat out of the guest room. I don't have to close the door anymore because the divider allows light and air through. Adds a nice touch to the decor, as well. Very lightweight and serves its purpose.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 3, 2026
★★★★★ 4
Good Room Divider
Size: 4 Panel, Color: White
This room divider worked great to mask my "utility area" in my living room because I'm low on storage space. It's functional and pleasing to the eye, but the quality could be better as there were pieces of debris on the unit and fraying strings. It also can tip over if not positioned just right. I do like the versatility of it though because even though it's a four panel I can fold in one of the panels and use the other three. Overall I like it, the price could be lower based on the quality but its good.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on September 30, 2025
recommand products
Ground Beef 5oz, Plain with Green Beans and 1/4th Cup Brown Rice + Avocado
14.95
Ground Beef 6oz, Taco Seasoned with Zucchini & Squash and 1/4th Cup Brown Rice + Avocado
16.95
Ground Beef 5oz, Taco Seasoned with Green Beans and 1/4th Cup Brown Rice + Avocado
14.95
Ground Beef 10oz, Taco Seasoned with Asparagus and 1/4th Cup Cranberry Almond Quinoa
24.95
Ground Beef 4oz, Taco Seasoned with Broccoli and 1/4th Cup Brown Rice + Avocado
12.95